
resolve forces on inclines into components, apply Newton’s second law to connected objects and accelerating frames, and build a model for the stopping length of a runaway-truck escape ramp.
Phase 3: Make Sense
Do Now. Stand on one foot on a tilted board in your mind. Which way does gravity pull? Which way does the board push? Sketch both arrows on a slope.
On a slope, the normal force on a box equals its full weight, mg.
One method for every problem. Choose the object or system. Draw its free-body diagram. Choose axes, ideally with one axis along the acceleration. Resolve every force into components along those axes. Write Fnet = ma separately for each axis, then solve. The examples below use that method on the situations an escape-ramp designer needs.
Inclines. On a slope at angle θ, tilt your axes to match it. The weight mg splits into mg sin θ down the slope and mg cos θ into the slope. The normal force balances the perpendicular part, FN = mg cos θ. Worked example: a 10 kg box on a 25° ramp has components (10)(9.8)(sin 25°) = 41.4 N along the slope and 88.8 N into it. Without friction it slides down at g sin 25° = 4.14 m/s2. That is the model you tested with the Unit 1 ramp.
The escape-ramp model. A truck entering an uphill gravel ramp has two backward forces along the slope: the component of its weight, mg sin θ, and the resistance of the gravel, which we model as friction μFN = μmg cos θ. Newton’s second law gives a deceleration
a = g(sin θ + μ cos θ)
and, with v2 = v02 − 2aL from Unit 1, the stopping length L = v02/(2a). The mass cancels, which is why one ramp works for a pickup and a loaded semi. Worked example (illustrative values): a truck enters at 31 m/s (69 mph) on a 10% upgrade (θ = 5.71°) with an effective gravel coefficient μ = 0.25, typical of loose pea gravel in highway design references. Then a = 9.8(sin 5.71° + 0.25 cos 5.71°) = 3.41 m/s2 and L = 312/(2 × 3.41) = 141 m. On level gravel the same truck would need 196 m. Each part of the design (the grade, the bed material, the length) can be treated as a separate sub-problem.
Connected objects: the Atwood machine. Masses of 3.0 kg and 2.0 kg hang on either side of a light pulley. Treat both as one system moving along the string. The net force is the difference in weights, (3.0 − 2.0)(9.8) = 9.8 N, and the mass being accelerated is 5.0 kg, so a = 1.96 m/s2. For the tension, look at one mass: for the 2.0 kg side, T − 19.6 = 2.0(1.96), so T = 23.52 N, between the two weights as it must be.
Contact forces. Push a 4 kg block with 24 N so that it pushes a 2 kg block ahead of it on a frictionless floor. The whole system accelerates at 24/6 = 4.0 m/s2. The front block needs 2 × 4.0 = 8 N, so the blocks push on each other with 8 N (a third-law pair), not 24 N.
Apparent weight. A 60 kg student stands on a bathroom scale in an elevator. The scale reads the normal force. At rest, FN = mg = 588 N. Accelerating upward at 1.5 m/s2, FN − mg = ma, so FN = 60(9.8 + 1.5) = 678 N, and a scale calibrated in kilograms reads 69.2 kg. Accelerating downward at 1.5 m/s2, it reads 498 N (50.8 kg). The student’s mass never changed.
Misconceptions. (1) The normal force on a slope is not mg; it is mg cos θ. (2) Use the angle of the slope, and check with a limiting case: at θ = 0 the component along the slope must vanish. (3) Tension in a rope holding an accelerating mass is not equal to that mass’s weight.
Use the one-method steps on every problem.
Build the ramp model.
Build a spreadsheet model of escape-ramp length. Column A: entry speed from 20 to 40 m/s in steps of 2. Columns B–D: stopping length L = v2/[2g(sin θ + μ cos θ)] for grades of 0%, 5% and 10% with μ = 0.25. Graph all three. Then answer: which change shortens the ramp more, raising the grade from 5% to 10% or raising μ from 0.25 to 0.35? Propose two possible solutions for the “deceleration” sub-problem based on your numbers. (Graph paper and a calculator are fine if you do not have a spreadsheet.)
We now have a working ramp model. Next, we revise our explanation of the runaway and brainstorm ramp concepts.
Exit ticket: write a = g(sin θ + μ cos θ) in words, naming the two forces that slow the truck and where each comes from.
Timing: Poly ran this as 2 × 50 min. Period 1: inclines and the ramp model; period 2: Atwood, contact forces, elevators and the spreadsheet.
Materials: protractors, graph paper, devices with a spreadsheet; an optional spring scale and pulley for an Atwood demo.
Listen for: FN = mg on a slope; sine and cosine swapped (check θ = 0); grade read as degrees.
Support / stretch: a component triangle template. Stretch: model a descending arrester bed, where gravity helps the truck, and find the μ needed to stop it in 200 m.
Reading: OpenStax Physics (high school), chapter 5.