
measure the frequencies and wavelengths of standing-wave harmonics, compute the wave speed, and compare it with the prediction v = √(T/μ), including uncertainty.
Instruction
From a traveling wave to a standing wave. Send a wave down a string tied at both ends. It reflects at each end and the reflected wave overlaps the incoming one. At most frequencies the overlapping waves blur into a jumble. At certain frequencies they add up to a steady pattern that does not seem to travel at all: a standing wave. Points that never move are nodes; points that swing the most are antinodes.
Why only certain frequencies? Both fixed ends must be nodes. Adjacent nodes are half a wavelength apart, so the string length L must hold a whole number of half-wavelengths: L = nλ/2, or λn = 2L/n for n = 1, 2, 3, and so on. These are the harmonics. Combine this with v = fλ: fn = n·v/(2L). Each harmonic’s frequency is a whole-number multiple of the fundamental f1 = v/(2L). This is a pattern you can test: if your measured frequencies go roughly 1 : 2 : 3 : 4, the model is working.
What sets the speed on a string? Two properties of the string. The tension T (in newtons) pulls each displaced piece back toward rest; more tension means a faster restoring pull and a faster wave. The linear mass density μ (mass per unit length, kg/m) is the inertia that resists being accelerated; a heavier string carries a slower wave. The model is v = √(T/μ). Check the units: N/(kg/m) = (kg·m/s2)·(m/kg) = m2/s2, and the square root is m/s.
Worked example (this lab’s setup, illustrative numbers). A 2.00 m length of string has mass 1.00 g, so μ = 1.00 × 10−3 kg / 2.00 m = 5.00 × 10−4 kg/m. A 100 g bag of coins hangs over the dowel, so T = mg = 0.100 × 9.8 = 0.98 N. The predicted speed is v = √(0.98/0.0005) = 44.3 m/s. With a vibrating length of L = 1.00 m, the fundamental is f1 = 44.3/(2 × 1.00) = 22.1 Hz, the second harmonic 44.3 Hz and the third 66.4 Hz.
Getting speed from your measurements. For each harmonic you measure the frequency (from the tone-generator app or by timing) and the wavelength (twice the node-to-node distance, or 2L/n). Then v = fλ. In the illustrative data below, the four harmonics give speeds of 43.2, 44.5, 43.9, 44.5 m/s, a mean of 44.0 m/s, which differs from the √(T/μ) prediction by -0.6%. The spread among the four values gives a rough uncertainty. A graph of f against n should be a straight line through the origin with slope v/(2L); its slope is a better estimate than any one point.
Scaling reasoning. Because v depends on the square root of T, doubling the hanging mass does not double the speed: it multiplies it by √2 ≈ 1.41, giving 62.6 m/s here. To double the speed you need four times the tension.
Common misconceptions. (1) “Nodes are where the string is fastest.” Nodes never move; antinodes move fastest. (2) “The wavelength is the length of one loop.” One loop is half a wavelength. (3) “The standing wave has zero speed, so v = fλ does not apply.” A standing wave is two traveling waves going opposite ways, each at v; the pattern stands still, the waves do not. Connect this to New Madrid: seismologists find wave speeds in rock the same way you do here, from measured times, distances and the properties of the medium, and that is why the warning times in Lesson 4.1 are slower under the soft sediment of the Missouri Bootheel than in hard rock.
📖 Read for this lesson
The reading opens over the lesson; close it to come back to exactly where you were. The checks below draw on it.
Lab: Standing Waves on a String: Measuring Wave Speed Two Ways
Question. Does the wave speed found from standing-wave measurements (v = fλ) agree with the speed predicted from the string’s tension and mass per length (v = √(T/μ))?
Materials
- About 2.5 m of thin, strong string (braided fishing line or kite string)
- A way to find the string’s mass: a digital pocket scale that reads to 0.01 g (an inexpensive jewelry or postal scale), or a kitchen scale used on a long bundle (weigh 20 m or more of the same string and divide)
- A smooth round dowel, broom handle or wooden-spoon handle taped firmly across the edge of a table or the back of a heavy chair to act as the pulley
- A zip bag of coins or metal washers (50-200 g), weighed on a kitchen scale, as the hanging mass
- A vibration source: a small 4-8 Ω speaker (from an old pair of computer speakers or a toy) driven by a free tone-generator app through a phone’s headphone output, with the string taped to a paper clip glued to the cone
- Tape measure or meter stick, masking tape, phone stopwatch
- Route B (no speaker): a long rope or a metal or plastic spring toy (slinky), with the far end tied to a doorknob or a heavy table leg
- Safety glasses or sunglasses with wrap-around lenses
- Wear safety glasses whenever the string is under tension: a snapped string or a slipping mass can whip toward the face.
- Keep the hanging bag low (under 20 cm above the floor) and keep feet clear; use no more than 200 g. Keep small children and pets away from the setup.
- The speaker runs from a phone or a small battery amplifier only, never from a wall outlet; keep the volume moderate to protect hearing.
- On the floor route, stretch the spring or rope only as far as it springs back, tie the far end securely, and never let go of a stretched end.
- Tell a parent or guardian before you clamp or tape anything to furniture, and remove all tape afterward.
Procedure
- Find μ: weigh a 2.00 m piece of the string on a 0.01 g scale, or weigh a bundle of 20 m or more on a kitchen scale and scale it down to 2.00 m. Compute μ = mass/length in kg/m.
- Tie one end to the speaker’s paper clip, run the string over the dowel and hang the bag of coins. Measure the vibrating length L from the speaker to the top of the dowel. Weigh the bag on the kitchen scale and compute T = mg.
- Start the tone generator at a low frequency and raise it slowly until the string forms one large, steady loop (n = 1); call the pattern steady when the loop count holds for 10 seconds. Record the frequency. Repeat three times for each of 1, 2, 3 and 4 loops, lowering the frequency below the pattern before each new tuning.
- For each pattern, measure the distance between adjacent nodes with the meter stick and double it to get λ. Compare with 2L/n.
- Change the hanging mass (for example add coins until the bag weighs double) and find the fundamental again to test how v depends on T.
- Route B: tie one end of the rope or spring to a doorknob or table leg and stretch it about 4 m along the floor. Shake your end side to side, adjusting the rhythm until a steady pattern of 1, 2 and then 3 loops forms. Time 10 shakes with the phone stopwatch for each pattern to get f, and lay the tape measure beside the rope to measure node spacing for λ. A phone propped on a chair and recording video makes the nodes easier to see on playback.
Data
| Harmonic n | Frequency f (Hz) | Node spacing (m) | λ (m) | v = fλ (m/s) |
|---|---|---|---|---|
| 1 | ||||
| 2 | ||||
| 3 | ||||
| 4 | ||||
| Illustrative sample (not real data): L = 1.00 m, hanging mass 100 g (T = 0.98 N), μ = 5.00 × 10−4 kg/m | ||||
| 1 (illustrative) | 21.6 | 1.000 | 2.000 | 43.2 |
| 2 (illustrative) | 44.5 | 0.500 | 1.000 | 44.5 |
| 3 (illustrative) | 65.8 | 0.333 | 0.667 | 43.9 |
| 4 (illustrative) | 88.9 | 0.250 | 0.500 | 44.5 |
| Illustrative mean v = 44.0 m/s; predicted √(T/μ) = 44.3 m/s; percent difference -0.6% | ||||
Analysis
- Claim-evidence-reasoning: Do your two speeds agree? State your mean v = fλ and your √(T/μ), the percent difference, and explain why the two methods should give the same number.
- Graph f against n. Is it a straight line through the origin? Use the slope (which equals v/(2L)) to find v and compare it with your mean.
- Uncertainty: use the spread of your four v values (highest minus lowest, divided by 2) as an uncertainty. Is the difference from √(T/μ) larger or smaller than that?
- Sources of error: the node at the speaker is not perfect, the string stretches under tension so μ decreases slightly, the dowel has friction, and judging the steadiest pattern is subjective. Which one would most likely make your v = fλ too high or too low, and why?
- When you doubled the tension, by what factor did the fundamental frequency change? Compare with the √2 predicted by the model.
If you cannot do this lab in person: PhET Wave on a String (Oscillate, Fixed End, no damping): produce 1, 2 and 3 loops, measure λ with the ruler and the period with the timer, and compute v = fλ for low and high tension. Or use the recorded run in this lesson’s reading (three tuning trials per harmonic) or the sample dataset in the table above, graph f against n, and complete every analysis question.
Formative check
Work through these before moving on. They are not graded — they tell you whether the standard below has landed yet.
A 1.20 m string fixed at both ends shows 3 loops. What is the wavelength?
Doubling the tension on a string doubles the wave speed.
Simulation & tools
Standing waves in Wave on a String
Choose Oscillate and Fixed End, set damping to zero, and turn on the rulers and timer. With tension at its highest setting, adjust the frequency slowly until you see a steady pattern of 1, then 2, then 3 loops. For each, record the frequency, measure λ with the ruler and compute v = fλ. Repeat at a lower tension. Question: does v stay the same for every harmonic at a given tension, and does it drop when the tension drops? No device: use the illustrative data in the lab table and answer the same question.
Open in a new tab ↗ · PhET Interactive Simulations, University of Colorado Boulder · CC BY 4.0
Write your lab’s claim-evidence-reasoning paragraph. Give your mean v = fλ, your √(T/μ) value and the percent difference, state your uncertainty, and name the source of error you think mattered most and which way it pushed your result.
How confident are you that you can find a wave speed from standing-wave measurements and compare it with a model prediction?
Practice
Work these on paper or in your notebook, then open Check your answer. Aim for all of Fluency and Application; try at least one Challenge.
Printable version: this unit’s practice workbook (PDF)
Fluency
Build speed and accuracy with the core skill.
- A sound in air (speed 343 m/s) has wavelength 1.0 m. What is its frequency?
Check your answer
Answer: 343.0 Hzf = v/λ. - A wave on a rope travels at 5 m/s. Find the wavelength for a frequency of 4 Hz.
Check your answer
Answer: 1.25 mλ = v/f. - A string 1.20 m long, fixed at both ends, vibrates in 3 loops. What is the wavelength?
Check your answer
Answer: 0.80 mλ = 2L/n. - A 1.5 m string has mass 1.5 g and is under the tension of a 150 g hanging mass. Find μ, the tension and the wave speed.
Check your answer
Answer: μ = 1.00 × 10−3 kg/m; T = 1.470 N; v = 38.3 m/sv = √(T/μ). - With that string vibrating over 0.90 m, what is the fundamental frequency, and what are the next two harmonics?
Check your answer
Answer: 21.3 Hz; 42.6 Hz and 63.9 Hzfn = nv/(2L). - By what factor must you increase the tension to double the wave speed on a string?
Check your answer
Answer: 4v ∝ √T.
Application
Use the skill in context. Show your reasoning.
- A student finds the fundamental of a 0.90 m vibrating length at 30.5 Hz. What wave speed does that give, and how does it compare with the model value above?
Check your answer
Answer: 54.9 m/s; 43.2% differencev = f × 2L. - What tension would make the fundamental of the 0.90 m string exactly 40 Hz?
Check your answer
Answer: 5.18 Nv = 2Lf = 72 m/s; T = μv2. - A friend says: “The standing wave doesn’t move, so v = fλ doesn’t apply.” Respond.
Check your answer
Answer: It applies to the two traveling waves that form the standing waveThe pattern stands still because equal waves travel in opposite directions, each at v = fλ.
Challenge
Stretch problems. Expect to think before you write.
- A guitar string’s fundamental is 110 Hz. Tightening it raises the tension by 21%. What is the new fundamental?
Check your answer
Answer: 121.0 Hzf ∝ v ∝ √T; √1.21 = 1.10.
Review
Keep earlier skills sharp.
- Resistors of 12 Ω and 15 Ω are in parallel across 3 V. Find the equivalent resistance and the total current.
Check your answer
Answer: 6.67 Ω; 0.450 A (branch currents 0.250 A and 0.200 A)Parallel: 1/R = 1/R1 + 1/R2; each branch has the full voltage. - A gas occupies 12 L at 200 kPa. At constant temperature, what volume does it occupy at 50 kPa?
Check your answer
Answer: 48.00 LBoyle’s law: P1V1 = P2V2.
Four Harmonics, Three Readings Each: A Recorded At-Home Standing-Wave Run
SLS constructed teaching data set (illustrative, not laboratory measurements) following the RLP Lesson 4.2 at-home procedure: 1.00 m vibrating length, 100 g bag of coins as the hanging mass, four harmonics, three tuning readings and three node-spacing readings per harmonic, plus a doubled-tension check; every derived value recomputed November 5, 2026 · SLS original
Why this reading. The lab table in the lesson gives one illustrative frequency and one node spacing per harmonic — a single number to type in, not a measurement to make. The analysis questions ask for a mean, a spread-based uncertainty and a doubled-tension check, none of which a single reading per row can supply. Below is a full recorded run of the lesson’s own setup: three tuning trials and three node-spacing trials per harmonic, plus the doubled-mass fundamental. Every mean in the lesson’s table is reproduced from these rows.
Setup
Recorded at home. Vibrating length L = 1.00 m (speaker to the top of a smooth wooden dowel taped across a table edge), string mass 1.00 g over the full 2.00 m piece read on a digital pocket scale to 0.01 g, so μ = 1.00 × 10−3 kg / 2.00 m = 5.00 × 10−4 kg/m. Hanging mass: a zip bag of coins weighed to 100.0 g (±0.1 g on the same scale), giving T = mg = 0.100 × 9.8 = 0.980 N. Predicted speed √(T/μ) = √(0.980/0.0005) = 44.27 m/s. Tone-generator app, headphone-out driven speaker, 4 Ω, frequency readout to 0.1 Hz. Node spacing measured with a tape measure to the nearest millimeter.
Table 1. Three tuning trials per harmonic
| Harmonic n | Trial 1 f (Hz) | Trial 2 f (Hz) | Trial 3 f (Hz) | Mean f (Hz) |
|---|---|---|---|---|
| 1 | 21.4 | 21.8 | 21.6 | 21.6 |
| 2 | 44.3 | 44.8 | 44.4 | 44.5 |
| 3 | 65.5 | 66.2 | 65.7 | 65.8 |
| 4 | 88.6 | 89.3 | 88.8 | 88.9 |
Each trial is a fresh tuning: the frequency was lowered below the pattern, then raised slowly until the loop count held steady for 10 seconds, and the readout was recorded each time. The spread within a harmonic (about ±0.3 to ±0.4 Hz) is the “how steady does it look” judgment call built into the procedure.
Table 2. Three node-spacing trials per harmonic
| Harmonic n | Trial 1 (m) | Trial 2 (m) | Trial 3 (m) | Mean spacing (m) | λ = 2 × spacing (m) | 2L/n predicted (m) |
|---|---|---|---|---|---|---|
| 1 | 1.002 | 0.996 | 1.001 | 1.000 (half-loop = whole string) | 2.000 | 2.000 |
| 2 | 0.498 | 0.503 | 0.499 | 0.500 | 1.000 | 1.000 |
| 3 | 0.335 | 0.331 | 0.334 | 0.333 | 0.667 | 0.667 |
| 4 | 0.252 | 0.248 | 0.249 | 0.250 | 0.500 | 0.500 |
Node spacing agrees with the 2L/n prediction to the nearest millimeter at every harmonic, which is what lets v = fλ be trusted as well as the tension model.
Table 3. Wave speed from each harmonic, and the doubled-tension check
| Harmonic n | Mean f (Hz) | λ (m) | v = fλ (m/s) |
|---|---|---|---|
| 1 | 21.6 | 2.000 | 43.2 |
| 2 | 44.5 | 1.000 | 44.5 |
| 3 | 65.8 | 0.667 | 43.9 |
| 4 | 88.9 | 0.500 | 44.5 |
Mean v across the four harmonics = (43.2 + 44.5 + 43.9 + 44.5)/4 = 44.0 m/s, against the predicted √(T/μ) = 44.3 m/s: a percent difference of (44.3 − 44.0)/44.3 = −0.6%. Spread-based uncertainty: (44.5 − 43.2)/2 = ±0.65 m/s, so the model value of 44.3 m/s falls inside the range 43.35 to 44.65 m/s — the two methods agree within the measurement’s own uncertainty.
Doubled-mass check. With coins added until the bag weighed 200.0 g, T = 1.96 N and the predicted speed is √(1.96/0.0005) = 62.61 m/s, a factor of √2 = 1.414 over the 100 g case. Three fundamental-frequency trials at 200 g: 30.6, 31.1, 30.8 Hz, mean 30.8 Hz. With L unchanged at 1.00 m, λ = 2.00 m, so v = 30.8 × 2.00 = 61.6 m/s. Ratio to the 100 g mean speed: 61.6/44.0 = 1.40, against the predicted 1.414 — a 0.99% difference, confirming the square-root relationship rather than a doubling.
Slope method
Graphing mean f against n (21.6, 44.5, 65.8, 88.9 at n = 1, 2, 3, 4) gives a line through the origin with slope Σ(n·f)/Σ(n2) = (21.6 + 89.0 + 197.4 + 355.6)/(1 + 4 + 9 + 16) = 663.6/30 = 22.12 Hz per harmonic number. Since fn = n·v/(2L), the slope equals v/(2L) = v/2.00, so v = 2.00 × 22.12 = 44.24 m/s — closer to the 44.27 m/s prediction than the four-point mean, because the slope uses all four points at once and is less swayed by any single harmonic’s tuning error.
Your turn
- Compute the percent difference between the slope-method speed (44.24 m/s) and √(T/μ) (44.27 m/s), and compare it with the four-point-mean percent difference (−0.6%). Which method agrees more closely, and why would you expect that?
- Using Table 1’s three trials for harmonic 2, compute that harmonic’s own spread-based uncertainty in frequency, then convert it to an uncertainty in v at fixed λ = 1.000 m.
- The node spacing for harmonic 1 (“half-loop = whole string”) could not be measured the same way as the others. Explain from the setup why n = 1 has no interior node to space between two points, and how λ is still found for it.
- If a source of error stretched the string slightly more at higher tension (so μ actually decreases a little as the hanging mass increases), would that make the doubled-mass ratio come out above or below the predicted √2, and why?