
calculate molarity, dilutions and parts-per-million and parts-per-billion concentrations, and argue from data whether a water sample or a water system meets a lead action level.
Instruction
Why concentration matters. The Missouri River at Hermann carries dissolved calcium, magnesium, sodium, sulfate, chloride and trace metals. On June 26, 2023, a U.S. Geological Survey sample from Hermann held 62.0 mg of dissolved calcium in each liter, and 4.4 micrograms of arsenic per liter (USGS data, this lesson’s reading). The same water also holds a pesticide, atrazine, at 507 nanograms per liter. Those three numbers are all concentrations, but they differ by a factor of a million. Chemists use several units to keep them readable.
Molarity. A solution is a solute dissolved in a solvent. Molarity is moles of solute per liter of solution, M = n ÷ V. To make 500 mL of 0.150 M sodium chloride, you need 0.150 × 0.500 = 0.0750 mol, and the molar mass of NaCl is 22.990 + 35.45 = 58.44 g/mol, so 0.0750 × 58.44 = 4.38 g, dissolved and then filled up to the 500 mL mark.
Dilution. Adding solvent changes the volume but not the moles of solute, so M1V1 = M2V2. To make 250 mL of 0.150 M from a 0.600 M stock, V1 = 0.150 × 250 ÷ 0.600 = 62.5 mL of stock, filled to 250 mL. Laboratories use the same relationship in reverse: if a water sample is diluted from 5.00 mL to 50.0 mL (a factor of 10) and the instrument reads 1.30 µg/L, the original sample was 1.30 × 10 = 13.0 µg/L.
Parts per million and parts per billion. For very dilute water solutions, 1 liter of water has a mass of about 1 kg, so 1 mg/L is one part per million (ppm) and 1 µg/L is one part per billion (ppb). The calcium is 62.0 ppm, the arsenic 4.4 ppb, and the atrazine 507 ng/L = 0.507 ppb. To convert to molarity, change the mass to grams and divide by molar mass: 62.0 mg/L = 0.0620 g/L ÷ 40.078 g/mol = 1.55 × 10−3 mol/L. A check on this kind of arithmetic: water hardness, expressed as calcium carbonate, is (Ca ÷ 40.078 + Mg ÷ 24.305) × 100.09. With Ca = 62.0 and Mg = 26.0 mg/L this gives 261.9 mg/L, and USGS reported 262.
Gases dissolve less in warm water. A different kind of solubility trend: the NIST Chemistry WebBook lists the Henry’s-law constant for carbon dioxide in water, 0.034 mol/(kg·bar) at 25 °C with a temperature factor of 2,400 K. Using it, Missouri River water at its coldest water temperature in the USGS sample record used for this lesson (1.4 °C, January 31, 2024) dissolves 2.26 times as much CO2 as water at its warmest (29.7 °C, July 25, 2022) at the same pressure. This is why a warm soda goes flat faster, and it is one reason river chemistry changes with the seasons.
The argument: lead in a tap. Lead is toxic; the U.S. Environmental Protection Agency has set its health goal for lead in drinking water at zero, because it finds no safe level of exposure. Because lead usually enters water from a customer’s pipes, EPA regulates it with a treatment technique: if more than 10 percent of tap samples exceed the action level, which has been 15 ppb, a water system must take further steps such as corrosion control and public education. EPA’s 2024 revision lowers the action level from 15 to 10 µg/L. In concentration terms, 15 ppb is about 7.24 × 10−8 mol/L, or 4.36 × 1016 lead atoms in every liter, which sounds enormous and shows why mass units are easier to read. Your task in this lesson is to argue, from a data set, whether a system passes or fails each level, and what the number does and does not tell us. In a good argument each claim names a number, a comparison and a limitation.
📖 Read for this lesson
The reading opens over the lesson; close it to come back to exactly where you were. The checks below draw on it.
Formative check
Work through these before moving on. They are not graded — they tell you whether the standard below has landed yet.
How many grams of NaCl (58.44 g/mol) are needed to make 500 mL of a 0.150 M solution?
A sample is diluted from 5.00 mL to 50.0 mL and reads 1.30 µg/L of lead. The original sample held µg/L.
If a water system’s samples are below the action level, EPA considers the water to contain a safe amount of lead.
Use the data table in this lesson’s reading. In the 20 illustrative tap samples, how many exceed 10 µg/L, and is that more than 10 percent of the samples?
Write a 5-7 sentence argument: using the 20 illustrative samples in this lesson’s reading, does the system trigger action at 15 µg/L, and at 10 µg/L? State each claim with the count and percent, and say what the action level does not tell you about whether the water is safe.
How confident are you that you can calculate molarity, dilutions and ppm or ppb concentrations and use them in an argument about a lead action level?
Practice
Work these on paper or in your notebook, then open Check your answer. Aim for all of Fluency and Application; try at least one Challenge.
Printable version: this unit’s practice workbook (PDF)
Fluency
Build speed and accuracy with the core skill.
- What is the molarity of a solution with 0.250 mol of solute in 0.500 L?
Check your answer
Answer: 0.500 M0.250 ÷ 0.500 = 0.500 mol/L. - What mass of NaCl (58.44 g/mol) is needed for 500 mL of 0.150 M solution?
Check your answer
Answer: 4.38 g0.150 × 0.500 = 0.0750 mol; × 58.44 = 4.383 g. - Express 15 ppb of lead in mg/L.
Check your answer
Answer: 0.015 mg/L15 µg/L = 0.015 mg/L. - How much 0.600 M stock is needed to make 250 mL of 0.150 M solution?
Check your answer
Answer: 62.5 mLV1 = 0.150 × 250 ÷ 0.600 = 62.5 mL. - Calculate the molar mass of CaCO3 from 40.078, 12.011 and 15.999 g/mol.
Check your answer
Answer: 100.09 g/mol40.078 + 12.011 + 3(15.999) = 100.086.
Application
Use the skill in context. Show your reasoning.
- USGS measured 62.0 mg/L of dissolved calcium in Missouri River water. Express this in mol/L (Ca 40.078 g/mol).
Check your answer
Answer: 1.55 × 10−3 mol/L0.0620 ÷ 40.078 = 1.547 × 10−3 mol/L. - The same sample held 174 mg/L of sulfate (SO42−, 96.056 g/mol using S 32.06 and O 15.999). Express this in mol/L.
Check your answer
Answer: 1.81 × 10−3 mol/L0.174 ÷ 96.056 = 1.811 × 10−3 mol/L. - Water hardness as CaCO3 = (Ca ÷ 40.078 + Mg ÷ 24.305) × 100.09, with Ca and Mg in mg/L. Find it for Ca = 62.0 and Mg = 26.0 mg/L.
Check your answer
Answer: 261.9 mg/L as CaCO3 (USGS reported 262)(62.0 ÷ 40.078 + 26.0 ÷ 24.305) × 100.09 = (1.5470 + 1.0697) × 100.09 = 261.9. - A laboratory dilutes a 5.00 mL tap sample to 50.0 mL and reads 1.30 µg/L of lead. What was the original concentration? Is it above 15 ppb? Above 10 ppb?
Check your answer
Answer: 13.0 µg/L; below 15 ppb but above 10 ppbThe dilution factor is 50.0 ÷ 5.00 = 10, so 1.30 × 10 = 13.0 µg/L.
Challenge
Stretch problems. Expect to think before you write.
- Use the 20 illustrative tap samples in this lesson’s reading. How many exceed 10 µg/L? How many exceed 15 µg/L? Under the ‘more than 10 percent of samples’ trigger, which levels require action?
Check your answer
Answer: 4 samples (20 percent) exceed 10, so action is triggered at 10 µg/L. 2 samples (exactly 10 percent) exceed 15, which is not more than 10 percent, so no action is triggered at 15 µg/L.Sorted values above 10: 10.8, 12.4, 16.3, 18.9. Above 15: 16.3 and 18.9. - How many lead atoms are in a 250 mL glass of water at 15 µg/L? Use Pb = 207.2 g/mol and 6.02214076 × 1023 per mole.
Check your answer
Answer: About 1.09 × 1016 atomsMass: 15 µg/L × 0.250 L = 3.75 µg = 3.75 × 10−6 g. Moles: 3.75 × 10−6 ÷ 207.2 = 1.81 × 10−8 mol. Atoms: 1.81 × 10−8 × 6.022 × 1023 = 1.09 × 1016. - Carbon dioxide’s Henry’s constant is 0.034 mol/(kg·bar) at 298.15 K with a temperature factor of 2,400 K: k(T) = 0.034 × exp[2400 × (1/T − 1/298.15)]. Compare the solubility at 1.4 °C and 29.7 °C at the same pressure.
Check your answer
Answer: The solubility at 1.4 °C (0.0679 mol/(kg·bar)) is 2.26 times that at 29.7 °C (0.0300 mol/(kg·bar)).At 274.55 K: 0.034 × exp(0.692) = 0.0679. At 302.85 K: 0.034 × exp(−0.125) = 0.0300. Ratio = 2.26.
Review
Keep earlier skills sharp.
- How many moles are in 50.0 g of CaCO3 (100.086 g/mol)?
Check your answer
Answer: 0.500 mol (0.4996 mol)50.0 ÷ 100.086 = 0.4996 mol. - A gas at 1.00 atm occupies 2.00 L. At constant temperature the pressure is lowered to 0.500 atm. What is the volume?
Check your answer
Answer: 4.00 LV2 = 1.00 × 2.00 ÷ 0.500 = 4.00 L.
Missouri River Water Chemistry and a Lead Action-Level Data Set: Data for Lesson 4.3
U.S. Geological Survey National Water Information System records for Missouri River at Hermann, MO (USGS 06934500) via the Water Quality Portal; EPA, Basic Information about Lead in Drinking Water and the Lead and Copper Rule Improvements fact sheet; KC Water, Information About Lead; NIST Chemistry WebBook Henry’s-law data for carbon dioxide; NIST atomic weights; all retrieved 2026-11-15. The 20 tap samples and the laboratory dilution report are SLS illustrative data · SLS original (prose, calculations and constructed illustrative data); USGS, EPA and NIST content is U.S. government information in the public domain; KC Water page cited by link
Why this reading. Concentrations only mean something when you can see real ones. This reading gives five USGS water analyses from the Missouri River at Hermann with their molarities, the EPA’s statements about the lead action level, 20 illustrative tap samples to argue about, a laboratory dilution report and the carbon dioxide solubility data for the lesson.
Missouri River at Hermann: five USGS analyses (2023, dissolved)
Concentrations in mg/L (ppm) unless noted; arsenic in µg/L (ppb); atrazine in ng/L; total dissolved solids as residue on evaporation at 180 °C; hardness as mg/L CaCO3, as reported by USGS.
| Date | Calcium | Magnesium | Sodium | Chloride | Sulfate | Arsenic (µg/L) | Atrazine (ng/L) | Dissolved solids | Hardness |
|---|---|---|---|---|---|---|---|---|---|
| 2023-06-26 | 62.0 | 26.0 | 60.5 | 24.7 | 174 | 4.4 | 507 | 476 | 262 |
| 2023-07-05 | 64.2 | 27.5 | 67.8 | 25.2 | 190 | 4.4 | 276 | 492 | 274 |
| 2023-07-24 | 57.0 | 23.6 | 62.0 | 24.1 | 178 | 4.0 | 173 | 451 | 240 |
| 2023-08-07 | 43.7 | 16.7 | 43.6 | 15.4 | 125 | 2.7 | 410 | 345 | 178 |
| 2023-10-23 | 56.5 | 26.1 | 71.5 | 23.0 | 205 | 3.3 | 103 | 502 | 249 |
Converting to molarity and checking hardness
Molarity = (mg/L ÷ 1,000) ÷ molar mass. Atomic weights (NIST): Ca 40.078, Mg 24.305, S 32.06, O 15.999; sulfate is 96.056 g/mol. Calculated hardness = (Ca ÷ 40.078 + Mg ÷ 24.305) × 100.09.
| Date | Calcium (mmol/L) | Sulfate (mmol/L) | Calculated hardness (mg/L) | USGS hardness (mg/L) |
|---|---|---|---|---|
| 2023-06-26 | 1.547 | 1.811 | 261.9 | 262 |
| 2023-07-05 | 1.602 | 1.978 | 273.6 | 274 |
| 2023-07-24 | 1.422 | 1.853 | 239.5 | 240 |
| 2023-08-07 | 1.090 | 1.301 | 177.9 | 178 |
| 2023-10-23 | 1.410 | 2.134 | 248.6 | 249 |
What EPA says about lead in tap water
- EPA’s health goal (maximum contaminant level goal) for lead is zero, because EPA finds no known safe level of lead exposure.
- Because lead mostly comes from customers’ plumbing, EPA regulates it with a treatment technique, the Lead and Copper Rule, rather than a maximum level. If more than 10 percent of tap samples exceed the lead action level of 15 parts per billion, a water system must take further steps such as corrosion control, public education and replacing lead service lines under its control.
- EPA’s 2024 Lead and Copper Rule Improvements lower the lead action level from 15 µg/L to 10 µg/L. In water, 1 µg/L is about 1 ppb.
- KC Water states that EPA rules required public water systems to complete an inventory of service-line materials by October 16, 2024.
Twenty illustrative first-draw tap samples (µg/L of lead)
Illustrative data for a made-up system, not measurements from any Missouri utility. Samples are sorted from lowest to highest.
| Sample | Lead (µg/L) | Above 15? | Above 10? |
|---|---|---|---|
| 1 | 0.5 | no | no |
| 2 | 0.8 | no | no |
| 3 | 0.9 | no | no |
| 4 | 1.2 | no | no |
| 5 | 1.4 | no | no |
| 6 | 1.9 | no | no |
| 7 | 2.2 | no | no |
| 8 | 2.5 | no | no |
| 9 | 2.9 | no | no |
| 10 | 3.1 | no | no |
| 11 | 3.6 | no | no |
| 12 | 4.8 | no | no |
| 13 | 5.1 | no | no |
| 14 | 6.2 | no | no |
| 15 | 7.4 | no | no |
| 16 | 8.7 | no | no |
| 17 | 10.8 | no | yes |
| 18 | 12.4 | no | yes |
| 19 | 16.3 | yes | yes |
| 20 | 18.9 | yes | yes |
Counts: 2 of 20 samples (10 percent) exceed 15 µg/L, which is not more than 10 percent; 4 of 20 samples (20 percent) exceed 10 µg/L, which is more than 10 percent.
Laboratory dilution report (illustrative)
Sample A: 5.00 mL of tap water diluted to 50.0 mL; the instrument reads 1.30 µg/L; original = 1.30 × 10 = 13.0 µg/L. Sample B: 2.00 mL diluted to 50.0 mL; reads 0.480 µg/L; original = 0.480 × 25 = 12.0 µg/L.
Lead in concentration units
Lead has a standard atomic weight of 207.2 g/mol (NIST). 15 µg/L = 15 × 10−6 ÷ 207.2 = 7.24 × 10−8 mol/L = 4.36 × 1016 atoms per liter. 10 µg/L = 4.83 × 10−8 mol/L.
Carbon dioxide dissolving in water, by temperature
The NIST Chemistry WebBook (compilation by R. Sander) lists the Henry’s-law constant for CO2 in water as 0.034 mol/(kg·bar) at 298.15 K, with a temperature factor of 2,400 K: k(T) = 0.034 × exp[2400 × (1/T − 1/298.15)]. USGS water temperatures at Hermann in the record used here run from 1.4 °C (January 31, 2024) to 29.7 °C (July 25, 2022).
| Water temperature (°C) | Temperature (K) | k (mol/(kg·bar)) |
|---|---|---|
| 1.4 | 274.55 | 0.0679 |
| 21 | 294.15 | 0.0379 |
| 29.7 | 302.85 | 0.0300 |
The ratio of the two river extremes is 2.26: cold water holds that many times more dissolved CO2 at the same pressure.
Sources: USGS records via Water Quality Portal, station USGS-06934500 (waterqualitydata.us); EPA: Basic Information about Lead in Drinking Water (epa.gov); EPA: Final Lead and Copper Rule Improvements fact sheet (epa.gov); KC Water: Information About Lead (kcwater.us); NIST Chemistry WebBook: carbon dioxide, Henry’s law data (webbook.nist.gov); NIST atomic weights and isotopic compositions (physics.nist.gov)