compare different sequences of transformations that map one figure onto another, decide when the order of moves matters, and choose a clear sequence to explain to an audience.
Phase 3: Make Sense
Do Now. Rosa and Ben both move the point (1, 0). Rosa rotates it 90° counterclockwise about the origin and then slides it 2 units right. Ben slides it 2 units right first and then rotates it 90° counterclockwise.
Do Rosa and Ben end at the same point?
The reading opens over the lesson; close it to come back to exactly where you were.
Many paths. There is often more than one sequence that maps a figure onto its image. Any sequence that works is a correct proof. Some are shorter or easier for an audience to follow.
Worked example 1: two routes, one image. Ibrahim maps triangle A(1, 0), B(3, 0), C(1, 2) onto A′(−1, 0), B′(−3, 0), C′(−1, −2). Route 1: rotate 180° about the origin, (−x, −y): (−1, 0), (−3, 0), (−1, −2). Route 2: reflect over the x-axis to (1, 0), (3, 0), (1, −2), then over the y-axis to (−1, 0), (−3, 0), (−1, −2). Both work. Route 1 is one step, so it is easier to explain.
When order matters. Swapping two moves can change the image. A rotation and a translation usually cannot be swapped (as Rosa and Ben found). A dilation about the origin and a translation cannot be swapped either, because the dilation also stretches the slide.
Worked example 2: a souvenir model. Valeria plans a sample souvenir model of the Statue of Liberty at a scale of 1 to 24. Step 1: the head is 10 feet = 120 inches wide, so the model’s head is 120 ÷ 24 = 5 inches. Step 2: the 8-foot index finger is 96 inches, so the model’s is 96 ÷ 24 = 4 inches. Step 3: on her shelf plan, a corner point at (2, 4) is dilated by 1/2 and then translated 3 right: (1, 2), then (4, 2). Step 4: if she translated first, she would get (5, 4), then (2.5, 2). Different spots, so she writes her steps in order.
Choosing a sequence for an audience. Use the fewest steps you can, name each move fully (center, angle, direction, line, scale factor), and show the coordinates after each step. That is what our council will see in the pitch.
Congruent or similar? If your sequence has only rigid motions, the figures are congruent. If it needs a dilation with a scale factor other than 1, they are similar but not congruent.
Show the point after every step. Change feet to inches before you divide.
Write each sequence in order with the point after each step.
Find two different sequences that map the segment from (0, 0) to (2, 0) onto the segment from (0, 0) to (0, −2). Which is simpler?
Which sequence maps (2, 4) to (4, 2)?
The statue’s nose is 4 feet 6 inches (54 inches) long. On a 1 to 24 model it is inches long. (Write the number with two decimal places.)
Different sequences can reach the same image, but order matters for some moves. Next we check everything we have learned and plan our park logo.
Exit ticket: give one pair of moves that can be done in either order, and one pair that cannot. Use a point to show each.
Pacing: Do Now 5 min, reading 7, mini lesson 11, guided practice 12, exit ticket 5.
Accuracy: all statue measurements (305 ft 1 in ground to torch, 111 ft 1 in heel to head, index finger 8 ft, head width 10 ft, mouth 3 ft, nose 4 ft 6 in, right arm 42 ft, copper 3/32 inch and 176,000 lb, sway 3 and 6 inches, 25 windows, seven rays, chains and shackle, the July 4, 1776 tablet, facing southeast) are from the NPS page. The 1 to 24 souvenir scale and the shelf coordinates are sample data.
Likely misconceptions: assuming any two moves can be swapped; dividing feet by 24 without changing to inches (8 ÷ 24 = 1/3 “inch”); thinking a longer sequence is “more correct.”
Supports: a step table (move, rule, point after the move). Stretch: is “reflect over the x-axis, then over the y-axis” the same as doing them in the other order? (Yes: both give (−x, −y).)
Answer guide: segment: rotate 90° clockwise about the origin, or rotate 90° counterclockwise then reflect over the x-axis; one rotation is simplest. Exit ticket example: reflect over the x-axis and translate right can be swapped ((2, 1) gives (5, −1) both ways); rotate 90° and translate right cannot (Rosa and Ben). Council reason: one clear step is easier to check.
National Park Service, Statue of Liberty National Monument: Statue Statistics · U.S. government work, public domain
The National Park Service lists official measurements for the Statue of Liberty in New York Harbor, in feet and inches and in meters.
From the ground to the tip of the torch, the statue and its pedestal stand 305 feet 1 inch tall. The statue alone, from heel to the top of the head, is 111 feet 1 inch. Some body parts are huge. The index finger is 8 feet long, the head is 10 feet wide, the mouth is 3 feet wide and the nose is 4 feet 6 inches long. The right arm is 42 feet long.
The statue’s copper skin is only 3/32 of an inch thick, which the page compares to two pennies placed together. The copper weighs 176,000 pounds. In the wind, the statue can sway up to 3 inches, and the torch up to 6 inches.
The crown has 25 windows and seven rays. Chains and a broken shackle lie at the statue’s feet, though they cannot be seen from below. The tablet in the statue’s hand reads July 4, 1776, in Roman numerals. The statue faces southeast.
Source: National Park Service, Statue of Liberty National Monument: Statue Statistics (nps.gov)