
design, test and refine a device that minimizes the force on a passenger in a collision, evaluate it against weighted criteria and trade-offs, and explain my material choice.
Instruction
The design problem
You now have the physics (impulse, stopping distance, conservation of momentum) and the materials science (structures that crush at a steady force). The task is an engineering one (9-12.PS2.A.3): design, build, test and refine a device that minimizes the force on a raw-egg passenger in a collision, then defend your choice of material. You may build an egg-drop package or a crumple zone for the crash-test cart from Lesson 3.4.
Criteria and constraints
Criteria are what success looks like; constraints are limits you cannot break (9-12.ETS1.A.2). Task criteria: the egg survives; the average force estimate is as small as possible; the device is light; it is cheap; and, ideally, it can be reused. Task constraints: at most 100 g of added material, no more than 25 cm on any side, only everyday materials that cost little or nothing (paper, card, cups, straws, tape, string, packing foam, balloons, cotton wool), no parachutes (so the test is about the impact, not the fall), and every test run in goggles.
Break the problem into sub-problems
A complex design is easier when you split it: (1) how will the egg be held so it cannot slide and hit a hard edge? (2) what will crush, and over how many centimeters? (3) how will you make the crush force steady rather than spiking at the end? Solve each part, test it, then combine them.
Using your model to set a target
Estimate before you build. For a 1.0 m drop, the egg arrives at 4.43 m/s. If you want the average force under about 20 N, you need F = mv2/(2d) ≤ 20 N, so d ≥ 0.060 × 4.432 / (2 × 20) = 2.9 cm of crush. Your crush zone must be thicker than that, because it cannot compress to zero thickness and because the peak force is above the average.
Evaluating trade-offs
No design wins on every criterion. A weighted decision matrix makes your priorities explicit (9-12.ETS1.B.1). Score each design 1-5 on each criterion, multiply by the weight, and add. Illustrative example:
| Design | Protection (highest safe drop) (weight 0.40) | Mass (weight 0.20) | Cost (weight 0.15) | Reusability (weight 0.25) | Weighted total |
|---|---|---|---|---|---|
| A: foam-cup cage | 4 | 3 | 5 | 2 | 3.45 |
| B: straw crumple zone | 5 | 4 | 4 | 1 | 3.65 |
| C: balloon airbag | 3 | 5 | 2 | 4 | 3.50 |
For design B: 0.40 × 5 + 0.20 × 4 + 0.15 × 4 + 0.25 × 1 = 3.65. Design B wins (3.65 against 3.50 and 3.45) because protection carries the most weight, even though it cannot be reused. If you weighted reusability more heavily, the balloon airbag might win. Your report must say why you chose your weights, and what social, cost or environmental considerations (for example, single-use foam waste) affected them.
Iteration
Keep an iteration log: for each version, what you changed, why, the test result (survived or not, crush distance, estimated force) and what you learned. Change one thing at a time so you know what caused the improvement. At least three tested versions are expected.
Communicating the material choice
Your final report explains, at the molecular or structural level, why your chosen material works (9-12.PS1.A.4): what its cells, tubes, folds or chains do when they are loaded, and why that gives a long, steady crush instead of a bounce or a shatter.
📖 Read for this lesson
The reading opens over the lesson; close it to come back to exactly where you were. The checks below draw on it.
Formative check
Work through these before moving on. They are not graded — they tell you whether the standard below has landed yet.
Using the weights 0.40, 0.20, 0.15, 0.25, what is the weighted total for a design scored 4, 4, 3, 3?
‘The device must weigh no more than 100 g’ is a constraint, while ‘the egg survives with the smallest possible force’ is a criterion.
Stage 1 check: list your criteria and constraints, your three sub-problems, and your target crush distance with the calculation that produced it.
How confident are you that you can design, test and refine a crash-safety device and justify it with data, trade-offs and materials science?
Unit 3 checkpoint
Do this before you start the task. It covers the whole unit and tells you what to review first.
Impulse equals
A 2.0 kg ball changes velocity from +3.0 to −2.0 m/s. The impulse on it is N·s.
A helmet protects the head by reducing its change in momentum.
A 0.40 kg cart at 1.2 m/s sticks to a 0.80 kg cart at rest. They move at m/s.
Momentum is conserved in a collision because
In a perfectly inelastic collision, kinetic energy is not conserved but momentum is.
A 0.5 kg puck moving east at 2.0 m/s hits a puck at rest. Afterward the first puck’s momentum is 0.5 kg·m/s north. What is the second puck’s momentum?
An egg moving at 5.0 m/s stops uniformly in 2.5 cm. The stopping time is ms.
Doubling the crush distance of a crumple zone halves the average force, for the same impact speed.
Why is a bike-helmet liner made of closed-cell foam?
A design scored 4, 3, 5 on criteria weighted 0.5, 0.3, 0.2 has a weighted total of .
‘The device must weigh less than 100 g’ is a criterion.
Submit: Crash-Safety Device design report (4-6 pages with data and diagrams) + 5-minute design defense
Task: Design, build, test and refine a device that protects a raw-egg passenger in a collision: either an egg-drop package dropped from a measured height of at least 1.5 m (no parachutes), or a crumple zone on the crash-test cart released from a marked ramp position. Your report must include: (1) the criteria and constraints and your weighted decision matrix with justified weights; (2) a sketch of each version with its materials; (3) an iteration log of at least three tested versions with speed, crush distance, stopping time, average force (Δp/Δt) and survival for each run; (4) a force-time sketch comparing your best design with an unprotected egg, with equal areas; (5) an explanation of why your chosen material works, based on its structure at the molecular or cellular level; and (6) an evaluation of trade-offs, including cost, reusability and waste, and one change you would make for a real bicycle helmet or car. Wear goggles for every test, drop from a sturdy step stool with an adult spotting you (never from a window, balcony or roof), and clean up broken egg immediately.
Choose where your test data come from. All three earn full credit and are the same difficulty.
Option A — build and test. As described above: at least three versions, each tested at least three times, with your own measurements.
Option B — the illustrative data set in this lesson. No materials needed. Four devices were dropped from 1.50 m, so every egg arrived at v = √(2 × 9.8 × 1.50) = 5.42 m/s, and every egg was 60 g. Stopping time is 2d/v and average force is mv2/(2d). These numbers are constructed to show the method; they are not real measurements.
| Design | Added mass (g) | Crush distance d (m) | Stopping time 2d/v (s) | Average force on the egg (N) | Egg survived? |
|---|---|---|---|---|---|
| No device (control) | 0 | 0.003 | 0.0011 | 294 | no |
| A: foam-cup cage | 85 | 0.045 | 0.0166 | 19.6 | yes |
| B: straw crumple zone | 62 | 0.075 | 0.0277 | 11.8 | yes |
| C: balloon airbag | 40 | 0.030 | 0.0111 | 29.4 | yes, but the shell cracked on one run in three |
Treat these as three tested versions plus a control. Recompute every stopping time and force yourself, build the iteration log from what changed between the designs (cup walls, straw tubes, trapped air), score them in your weighted matrix, and recommend and defend one. Then answer two extra questions: why design C is marginal at 29.4 N, and what would happen to each force if the drop were raised to 2.00 m.
Option C — PhET Collision Lab. The PhET Collision Lab simulation, at phet.colorado.edu/sims/html/collision-lab/latest/collision-lab_all.html, has an Explore 1D screen for this. Send a 0.060 kg ball into a much heavier ball at 5.4 m/s, and record its velocity change at 0% elasticity (it stops) and at 100% (it bounces). Use Δp = mΔv with three stopping times you choose (0.001 s, 0.010 s and 0.030 s) to build your force-time comparison and your iteration log, and say which real design change buys each stopping time. Cite the sim and the date you used it.
Submission workflow
- Stage 1 — Plan. Criteria and constraints, three sub-problems, two candidate designs with sketches, a target crush distance calculated from your drop height or cart speed, and a draft decision matrix with weights.
- Stage 2 — Self-checked draft. After at least two tested versions, recompute two of your force estimates a second way (once as mv2/(2d) and once as Δp/Δt), recheck your matrix arithmetic, and write the strongest challenge you can to one of your weights (or ask a family member to challenge it); answer it in a revision note.
- Stage 3 — Revised final. 4-6 pages with the full iteration log (at least three versions), the force-time comparison, the materials explanation and the trade-off evaluation.
- Stage 4 — Five-minute recorded design defense. Record a video or a narrated slide set that shows your final test, justifies your material choice and answers two questions about your model: how your average force would change if the drop height doubled, and why the peak force is larger than the average force you calculated.
How it is scored
| Criterion | What proficient looks like |
|---|---|
| Design and refinement (9-12.PS2.A.3) | The device is built and tested in at least three versions; each change is justified by data and the final design measurably reduces the force. |
| Impulse model (9-12.PS2.A.2) | Speed, stopping time and average force are computed correctly from measurements, with units, and the force-time sketch shows equal areas. |
| Criteria, constraints and sub-problems (9-12.ETS1.A.2) | Criteria and constraints are specific and measurable, and the problem is broken into sub-problems that are solved and tested. |
| Trade-off evaluation (9-12.ETS1.B.1) | The weighted matrix is computed correctly; weights are justified, including cost, reusability and environmental impact. |
| Materials explanation (9-12.PS1.A.4) | The material’s performance is explained from its molecular or cellular structure, distinguishing crushing, elastic rebound and brittle fracture. |
| Communication (SEP.8, RST.11-12.7) | Data tables, graphs and sketches are integrated with the text; the defense answers questions accurately. |
Crash-Device Test Runs: The Drops Behind the Four Designs, the 2.00 m Recompute, and the Matrix Inputs
SLS original run-by-run record for the task’s four egg-drop designs (1.50 m, 60 g egg), recomputation at 2.00 m, and illustrative material mass, cost and waste notes; CPSC helmet drop parameters from 16 CFR 1203.17 (Cornell LII, retrieved Nov. 5, 2026) · SLS original (CC BY 4.0); constructed teaching data, labeled illustrative; regulation quoted as published (public domain)
Why this reading. Option B tells you to treat the task’s four-design table as three tested versions plus a control, to build an iteration log from it, and to answer what happens at 2.00 m. A table of means is not an iteration log; a log records runs. Here are three drops per design, the arithmetic at both heights, the real drop test a helmet faces for comparison, and the material notes (mass, cost, waste) the decision matrix needs. Illustrative, except the CPSC figures.
1. The drops
Height 1.50 m, so every egg arrives at v = √(2 × 9.8 × 1.50) = 5.42 m/s. Egg mass 0.060 kg. Crush distance from the device’s height before and after, checked on 30 fps video. Stopping time 2d/v; average force mv2/(2d). The last column recomputes the force for a 2.00 m drop (v = 6.26 m/s) with the same crush distance, which is the task’s extra question.
| Design | Added mass (g) | d run 1 (m) | d run 2 | d run 3 | Mean d (m) | 2d/v at 1.50 m (s) | Average force at 1.50 m (N) | Force if dropped from 2.00 m (N) | Egg survived (3 runs) |
|---|---|---|---|---|---|---|---|---|---|
| No device (control) | 0 | 0.003 | 0.004 | 0.002 | 0.003 | 0.0011 | 294.0 | 392.0 | no, no, no |
| A: foam-cup cage | 85 | 0.045 | 0.047 | 0.043 | 0.045 | 0.0166 | 19.6 | 26.1 | yes, yes, yes |
| B: straw crumple zone | 62 | 0.075 | 0.079 | 0.071 | 0.075 | 0.0277 | 11.8 | 15.7 | yes, yes, yes |
| C: balloon airbag | 40 | 0.030 | 0.033 | 0.027 | 0.030 | 0.0111 | 29.4 | 39.2 | yes, yes, cracked |
The means reproduce the task table: 294, 19.6, 11.8 and 29.4 N. At 2.00 m every force rises by the factor 2.00/1.50 = 1.33, because v2 = 2gh and d was held fixed; in reality a device that crushed 0.030 m at 1.50 m will crush further at 2.00 m if it has material left, and bottom out if it does not. Design C is the case to watch: its 0.030 m is already the balloon’s full travel, its 29.4 N is the highest of the three, and it cracked one egg in three at 1.50 m. At 2.00 m it would be at 39 N with nothing more to give.
2. What the iteration log is made of
The three devices differ in one structural idea each. A (cups) puts thin paper walls in compression: they crush at a steady force and stay crushed. B (straws) puts many thin tubes in compression: more travel (0.075 m) at a lower force, but the tubes are single use and the device is bulky. C (balloon) traps air: light and reusable, but air springs back, so the egg rebounds and the shell carries a larger impulse than the average force suggests. Write each transition in the log as “changed X because run data showed Y; result Z.” For instance: A to B, changed the crushing element from cups to straws because A’s crush distance was 0.045 m and the target from the model was at least 0.029 m with margin for a non-constant force; result: force fell from 19.6 to 11.8 N with 0.030 m more travel.
3. The test a real helmet faces
The federal bicycle-helmet rule (16 CFR 1203.17) drops a helmeted 5.0 kg headform onto a flat anvil at 6.2 m/s, about a 2 m fall, and onto hemispherical and curbstone anvils at 4.8 m/s, about 1.2 m, and fails any helmet whose peak headform acceleration exceeds 300 g (section 1203.12). Your 2.00 m egg drop is the same experiment scaled down by a factor of 83 in mass. An egg shell’s tolerance is not published the way a headform’s is, but the survival column is your version of the pass-fail criterion, and the average-force column is your version of the accelerometer.
4. Material notes for the matrix (illustrative)
| Material | Mass as used (g) | Cost | Reuse and waste | Behavior on impact |
|---|---|---|---|---|
| Paper or foam cups (4) | about 20 | very low | single use; recyclable if clean | crush and stay crushed |
| Drinking straws (20) | about 10 | very low | single use; plastic waste | buckle and stay buckled |
| Balloon (1, inflated) | about 5 | very low | reusable until it pops | springs back; returns energy |
| Corrugated cardboard, 15 x 15 cm folded | about 25 | free (scrap) | single use; recyclable | folds and stays folded |
| Packing foam block, 10 x 10 x 5 cm | about 15 | free (scrap) | reusable a few times | partly recovers |
Score each design 1 to 5 on each criterion, multiply by your weights, add. The lesson’s worked matrix (weights 0.40 protection, 0.20 mass, 0.15 cost, 0.25 reusability) gives 3.45, 3.65 and 3.50 for A, B and C. Now ask what the matrix is sensitive to. If you decided that single-use plastic waste should count as a cost, B’s straws would lose points on a criterion that currently rewards them; if protection were weighted 0.50, B would win by more. Your report must state your weights and defend them, including the social and environmental reasons, and then show the ranking under one alternative weighting so the reader can see how robust the choice is.
Your turn (Stage 1 and 2 support)
- Recompute the 1.50 m force for design B from its three runs and confirm 11.8 N. Then compute the force for B’s worst run.
- Compute the target crush distance for a 20 N average force at 1.50 m (the lesson does it for 1.0 m). Which designs meet it, and by what margin?
- Build your decision matrix with a fifth criterion, waste, and explain in two sentences how you weighted it and what it did to the ranking.
- Sketch the force-time graphs for design B and for the control on one set of axes with equal areas (the impulse is 0.060 × 5.42 = 0.325 N·s in both cases), and label the peak of each.
Sources: 16 CFR 1203.17, Impact attenuation test (Cornell LII) (law.cornell.edu); 16 CFR 1203.12, Test requirements (Cornell LII) (law.cornell.edu)