
refine the conditions of a chemical system using equilibrium and rate calculations, evaluate the options against prioritized criteria and defend the design with evidence.
Instruction
The context. Missouri makes much of the lime and cement the country uses, and the United States makes about 14 million metric tons (as nitrogen) of ammonia a year, mostly for fertilizer (USGS Mineral Commodity Summaries 2026). Behind each number is an engineer who chose temperature, pressure and a way to remove product. In this task you take that role for a small process and defend your design with calculations.
The method. Start with the criteria: what the process must achieve (yield, speed), what it must not do (exceed a safe pressure) and what you want to keep low (fuel, equipment strength). Then rank the criteria and weight them. Evaluate each candidate condition on every criterion with the data package, show a model calculation with Q and K, and choose. Finally name the trade-off you accepted and what would change your mind.
Worked example: scoring one candidate for Brief A. Take 450 °C and 200 bar. The data package gives 24.6% NH3 at equilibrium and a relative rate index of 8.46 (350 °C = 1.00). Compare 350 °C and 200 bar: 47.0% NH3 but an index of only 1.00. The yield ratio is 1.91, while the rate ratio is 8.46 the other way. Which wins depends on your criteria: if reaching equilibrium within the time the gas spends on the catalyst matters most, the hotter bed is better; if the amount of NH3 per pass matters most, the colder bed is.
Model calculation. Pick your conditions and show the check: calculate K from the fit, write the expression for Kp, show that your table value is consistent (for example by calculating Q from the equilibrium partial pressures), and say what the table assumes (ideal gas, stoichiometric feed). A short argument for why your choice beats at least two alternatives should name specific numbers.
Brief B. If you choose the lime kiln, the data package gives K = P(CO2) at several kiln temperatures. A kiln that keeps CO2 pressure low needs a lower temperature than one that lets gas build up: for example the fit gives 797 °C at 0.20 bar and 760 °C at 0.10 bar. Design the airflow, temperature and stone size, and justify them with K, Q and rate ideas.
Before you start. Check the rubric, work out your criteria and weights on paper, and plan how you will present uncertainty honestly. The data are models; say so.
📖 Read for this lesson
The reading opens over the lesson; close it to come back to exactly where you were. The checks below draw on it.
Formative check
Work through these before moving on. They are not graded — they tell you whether the standard below has landed yet.
In the data package, going from 350 °C to 450 °C at 200 bar changes the NH3 equilibrium percent from 47.0 to 24.6 and the rate index from 1.00 to 8.46. Which statement best describes the trade-off?
A decision table is complete if it ranks designs on yield alone.
Draft your plan: name your brief, list your criteria in priority order, name at least three candidate conditions from the data package and write the equilibrium expression you will use.
How confident are you that you can refine a chemical system with equilibrium and rate evidence and defend the trade-offs?
Unit 2 checkpoint
Do this before you start the task. It covers the whole unit and tells you what to review first.
Which change would NOT speed up a reaction between a solid and a liquid?
A reactant falls from 0.800 M to 0.620 M in 90 s. The average rate is × 10−3 M/s.
With Ea = 50.0 kJ/mol, the rate at 305.35 K compared with 277.55 K is about
A 10 °C rise roughly doubles many reaction rates even though the average kinetic energy rises only a few percent.
A recorded mean time of 37.7 s gives a rate of × 10−3 s−1.
For CaCO3(s) ⇌ CaO(s) + CO2(g), the equilibrium expression is
At equilibrium the forward and reverse reactions have stopped.
At equilibrium [SO2] = 0.0400 M, [O2] = 0.0200 M and [SO3] = 0.0800 M, so Kc for 2 SO2 + O2 ⇌ 2 SO3 is .
For N2O4 ⇌ 2 NO2 (Kp = 0.148), Q = 0.45 for a mixture. The mixture will
For the exothermic reaction N2 + 3 H2 ⇌ 2 NH3, which condition gives the largest equilibrium yield of NH3?
Adding a catalyst to an equilibrium mixture changes the equilibrium constant.
At 450 °C the fitted K for ammonia synthesis is 4.43 × 10−5 bar−2. If P(N2) = 40.0 bar and P(H2) = 120. bar at equilibrium, P(NH3) = bar (three significant figures).
A design improves the equilibrium yield but makes the reactor much slower. The best description is
Refine a Chemical System: Design Memo and Defense
Task: Choose one design brief and refine its operating conditions. Your answer is a 700 to 1,000 word design memo with a decision table, plus a recorded four-minute defense.
Brief A: an ammonia synthesis loop. A small plant must make as much ammonia as possible per pass from a 1 : 3 mixture of N2 and H2, without exceeding a pressure that the plant’s equipment can hold safely. Use the data package in this lesson’s reading to compare at least four combinations of temperature and pressure.
Brief B: a lime kiln. A kiln must turn limestone into quicklime, CaCO3(s) ⇌ CaO(s) + CO2(g), using as little fuel as practical. Use the kiln table to compare at least three operating temperatures and CO2 pressures.
Your memo must: (1) state your prioritized criteria and weights (9-12.ETS1.B.1); (2) write the equilibrium expression and calculate at least one K or Q for your choice (9-12.PS1.B.2); (3) explain with collision theory and activation energy how your conditions change the rate, including the role of a catalyst or a sweep gas (9-12.PS1.B.1); (4) give a decision table of candidates with the numbers from the data package; (5) state the trade-off you accepted, the model’s limits and what result would change your mind; (6) cite the data package and at least one source from a lesson reading.
Submission workflow
- Stage 1 — Plan. Name your brief, your criteria and weights, and the candidates you will compare, and sketch the calculation you will show.
- Stage 2 — Reviewed draft. An adult reader (a parent, guardian or other adult) reads the draft as a non-scientist and checks that every number in the decision table traces back to the data package; you keep their notes and write a revision plan.
- Stage 3 — Final memo. 700 to 1,000 words with the equilibrium calculation, the decision table and the cited sources.
- Stage 4 — Recorded defense. Four minutes, recorded, ending with your answer to this question: what single change would you make to your design if the pressure limit were halved, and why?
How it is scored
| Criterion | What proficient looks like |
|---|---|
| Equilibrium calculation (9-12.PS1.B.2) | Correct K or Q expression and calculation, correct direction of shift and clear use of the data package. |
| Rate reasoning (9-12.PS1.B.1) | Uses collision theory and activation energy accurately to explain the effect of temperature, concentration, pressure or a catalyst. |
| Criteria and trade-offs (9-12.ETS1.B.1) | States prioritized criteria with weights, compares candidates on every criterion and names the trade-off accepted. |
| Evidence and sources (RST.11-12.7) | Every number comes from the data package or a cited source and the limits of the model are stated. |
| Communication (SEP.8) | Clear, organized memo and a defense that answers the closing question with evidence. |
Design Brief Data Package: Ammonia Loop and Lime Kiln
Calculated by SLS 2026-11-15 from the equilibrium-constant fit in Zhang, Way and Wolden (osti.gov/servlets/purl/1779196) and the CRC CO2-over-CaCO3 table reproduced on Wikipedia; USGS Mineral Commodity Summaries 2026 for Missouri’s rank · Public domain (USGS, NIST and DOE-hosted data), with SLS commentary and model calculations
Why this reading. It is the complete data package for the performance task. Both design briefs can be finished from the tables here, with no outside data needed.
Brief A: an ammonia synthesis loop
The model feeds nitrogen and hydrogen in the stoichiometric ratio 1 : 3 and assumes ideal gases and the equilibrium-constant fit given in Lesson 2.4’s reading (K = 2.03 × 10−12 exp(101,600 J/mol ÷ RT), bar−2). The table gives the mole percent of NH3 in the gas at equilibrium. Real gases at 200 bar and above are not ideal, so use the table to compare designs, not to predict a plant.
| °C | Relative rate index (350 °C = 1.00) | NH3 % at 50 bar | at 100 bar | at 200 bar | at 300 bar |
|---|---|---|---|---|---|
| 350 | 1.00 | 24.1 | 35.2 | 47.0 | 53.8 |
| 400 | 3.15 | 14.7 | 23.6 | 34.6 | 41.5 |
| 450 | 8.46 | 9.0 | 15.5 | 24.6 | 30.9 |
| 500 | 20.00 | 5.6 | 10.1 | 17.2 | 22.5 |
| 550 | 42.60 | 3.6 | 6.7 | 12.0 | 16.3 |
The relative rate index is illustrative: it assumes an activation energy of 80 kJ/mol for the catalyzed reaction, and it shows how quickly a catalyst-bed reaction speeds up as the bed gets hotter. The index is calculated by SLS and is not a measured rate.
Equipment strength and compressor work both grow with pressure, so use the pressure itself in bar as a rough measure of cost and risk. Anhydrous ammonia is toxic and corrosive, so a leak at 200 bar is a serious hazard (SLS note).
Brief B: a lime kiln
For CaCO3(s) ⇌ CaO(s) + CO2(g), the fit to the tabulated CO2 pressures (ΔH ≈ 175 kJ/mol) gives the following equilibrium values. The kiln makes quicklime only when the CO2 pressure at the stone is kept below the equilibrium value.
| Kiln temperature (°C) | K = equilibrium P(CO2) in bar | Equilibrium P(CO2) (kPa) |
|---|---|---|
| 700 | 0.028 | 2.8 |
| 750 | 0.082 | 8.2 |
| 800 | 0.213 | 21.3 |
| 850 | 0.509 | 50.9 |
| 900 | 1.130 | 113.0 |
Fuel burned to heat the kiln grows with temperature (a design cost in your decision matrix). For context, the U.S. Geological Survey reports that Missouri is one of the four leading lime-producing states and the second leading cement-producing state.
Check your model
- At 450 °C and 200 bar the model gives 24.6% NH3.
- The kiln table gives K = 0.213 at 800 °C.
Sources: Zhang, Way, Wolden: Catalytic Membrane Reactors for Ammonia Synthesis (OSTI) (osti.gov); USGS Mineral Commodity Summaries 2026: Lime (pubs.usgs.gov); USGS Mineral Commodity Summaries 2026: Cement (pubs.usgs.gov)