identify the angles formed when parallel lines are cut by a transversal and use them to find unknown angles in stairs and roof frames.
Phase 4: Build
Do Now. Picture the side of a staircase. The treads (the steps you stand on) are all level. A long board called a stringer runs under them at a slant. Sketch three level lines and one slanted line crossing all three.
The stringer crosses the first tread at a 37° angle. What angle does it make with the third tread, in the same position?
The reading opens over the lesson; close it to come back to exactly where you were.
Parallel lines and a transversal. Parallel lines never meet. A transversal is a line that crosses two or more lines. When a transversal crosses two parallel lines, it makes eight angles, four at each crossing. Many of them are equal.
The angle pairs. Corresponding angles sit in the same position at each crossing, such as upper right and upper right; they are equal. Alternate interior angles are between the parallel lines on opposite sides of the transversal; they are equal. Alternate exterior angles are outside the parallel lines on opposite sides; they are equal. Same-side interior angles are between the lines on the same side; they are supplementary. Vertical angles are still equal at each crossing.
Worked example 1: Keisha’s stair stringer. The treads are parallel, and the stringer is the transversal. The stair angle at the first tread is 37°. The corresponding angle at every other tread is also 37°. The angle beside it on the same tread line is 180 − 37 = 143°. Is the stair legal? 37 is between 30 and 50, so yes.
Worked example 2: Diego’s roof rafters. Two rafters are parallel. A collar tie crosses both. One alternate interior angle is 70°, and the other is (2x + 14)°. Alternate interior angles are equal, so 2x + 14 = 70. Subtract 14: 2x = 56. Divide by 2: x = 28. Check: 2(28) + 14 = 70.
Only when parallel. These equal-angle facts work only if the lines really are parallel. That is why builders use a level on every tread. If the lines are not parallel, the corresponding angles are not equal.
Argue it. On your Frame and Stair Plan, name the angle pair you used for every unknown angle. A volunteer should be able to follow your reasoning, not just your answer.
Sketch the parallel lines and the transversal. Label the pair before you solve.
Draw your Frame and Stair Plan sketch.
Draw three parallel treads and a stringer at 40°. Label all twelve angles. Name one pair of each kind: corresponding, alternate interior, alternate exterior and same-side interior.
Same-side interior angles at two parallel rafters measure (x + 40)° and (3x)°. Write and solve an equation, then find both angles.
Level treads make parallel lines, and parallel lines make angles that repeat.
Exit ticket: why does a builder check that every tread is level before using the corresponding-angle fact?
Pacing: warm-up and reading 7 minutes, mini lecture 9, career 3, guided practice 12, independent 7, closure 2.
Likely misconceptions: applying equal-angle facts to lines that are not parallel (Mia’s statement); mixing up interior and exterior; treating the obtuse angle as the stair angle. Note that OSHA measures the stair angle from horizontal.
Supports: a color-coded diagram (one color per equal family); tracing paper to slide one crossing onto the other and see the angles match. Stretch: show that alternate interior angles are equal by combining a corresponding pair and a vertical pair.
Answer guide: same-side interior; 42; 45; 40; true; 15; no, 52°. Mia: only when the lines are parallel. Independent: angles 40 and 140 repeat at each tread; x + 40 + 3x = 180, 4x + 40 = 180, 4x = 140, x = 35, angles 75° and 105°. Exit ticket: the facts hold only for parallel lines; level treads are parallel.
Occupational Safety and Health Administration, 29 CFR 1926.1052, Stairways · U.S. government work, public domain
OSHA writes safety rules for construction sites, and Section 1926.1052 is about stairways. Many of its rules are measurements.
The first is an angle rule: stairs must be installed between 30° and 50° from horizontal. Horizontal means level, like the floor.
The second rule is about matching steps. Each step has a riser, the vertical part, and a tread, the flat part you step on. OSHA says riser height and tread depth must be uniform, or the same, within each flight of stairs. Within any stairway system, the heights and depths cannot vary by more than 1/4 inch.
The third rule is about the stairrail people hold. Stairrails installed after March 15, 1991, must be at least 36 inches high, measured from the top of the rail down to the surface of the tread at the front edge.
When every tread is level, the treads are parallel. The slanted board that holds them, the stringer, crosses each tread at the same angle.
Source: Occupational Safety and Health Administration, 29 CFR 1926.1052, Stairways (osha.gov)