convert board sizes between fractions, decimals and percents and calculate with them to plan a cut or a stack.
Phase 2: Investigate
Do Now. Your teacher holds up a short piece of a “two by four” board. Measure its thickness and width with a ruler. Write what you find.
A board sold as a “two by four.” How thick do you think it really is?
The reading opens over the lesson; close it to come back to exactly where you were.
Numbers in any form. A tape measure shows fractions like 1½. A calculator shows decimals like 1.5. A store sign might say “20% off.” Builders switch forms to make a problem easier, and they keep the value the same.
Three ways to write one amount. 1½ = 1.5 = &frac32;. To change a fraction to a decimal, divide the numerator by the denominator: 3 ÷ 2 = 1.5. To change a decimal to a percent, multiply by 100: 0.75 = 75%.
Worked example 1: how big is the real board? Aiyana compares the real thickness with the nominal thickness. Step 1: write a fraction: 1.5 out of 2 is 1.5 ÷ 2. Step 2: divide: 1.5 ÷ 2 = 0.75. Step 3: write a percent: 0.75 = 75%. The real thickness is 75% of the name. For the width, 3.5 ÷ 4 = 0.875 = 87.5%.
Worked example 2: shrinking boards. NIST gives an example rule: about 1% shrinkage for each 4% change in moisture content. Marcus’s board is 3.5 inches wide and its moisture drops 8%. Step 1: 8 ÷ 4 = 2, so the board shrinks about 2%. Step 2: 2% = 0.02, and 0.02 × 3.5 = 0.07 inch. Step 3: 3.5 − 0.07 = 3.43 inches. Check: 0.07 is small next to 3.5, which fits a small percent.
Choose the easy form. Adding six thicknesses of 1½ inches? Decimals work well: 6 × 1.5 = 9 inches. Finding a part of a whole? Fractions or percents may be easier. Ordering amounts? Change them all to decimals.
Precision matters. If our plan says 2 inches when the board is 1.5 inches, a planter built from 6 stacked boards would be 3 inches shorter than planned (12 − 9 = 3). That is why our plan always uses actual sizes.
Use fraction strips or a ruler to show each conversion before you compute.
Add a “Real board sizes” table to your notebook.
A planter side uses 5 boards stacked on edge, each 3½ inches wide. How tall is the side? Write the answer as a decimal and as a mixed number.
Which list is in order from least to greatest?
A friend says, “Six two by fours stacked flat make 12 inches.” Explain the mistake and give the real height.
Board sizes are fractions, decimals and percents in disguise. Next we use bar models to find a mystery number in a cost equation.
Exit ticket: write ⅜ as a decimal and as a percent. Show your division.
Pacing: Do Now with measuring 6 min, reading 7, mini lesson 12, guided practice 10, exit ticket 5.
Materials: one short scrap of a 2×4 per table (sanded ends), rulers, fraction strips.
Accuracy: 1.5 by 3.5 inches (38 by 89 mm), the meaning of nominal size and the 1%-per-4% example are from the NIST story (March 2017). NIST gives the shrinkage figure as an example that varies by species, so present it as an example rule, not a law. Real scraps may measure a little differently; that is a good discussion of moisture and precision.
Likely misconceptions: 3½ = 3.12 (reading the fraction digits as decimals); 1.5 is 15% of 2; subtracting 3 instead of 3% of 3.5.
Answer guide: 5 × 3.5 = 17.5 = 17½ inches. The friend used the nominal 2 inches; real height is 6 × 1.5 = 9 inches. Exit ticket: ⅜ = 0.375 = 37.5%.
National Institute of Standards and Technology, Making Sure that Lumber Measures Up (news, March 2017) · U.S. government work, public domain
The National Institute of Standards and Technology, or NIST, helps make sure measurements in stores are fair. This news story is about lumber. It points out something that surprises many people: a “two by four” board actually measures about 1.5 inches by 3.5 inches, or 38 by 89 millimeters.
The name “two by four” is a nominal size. That means it is a name for the approximate size, not the actual size. The story explains that nominal sizes came from the size of rough boards before a mill made them smooth and even.
Measuring lumber is harder than it sounds. The size of a board changes with how much water is in the wood, called its moisture content. Size also depends on the kind of tree and the direction of the grain. The story gives an example of a correction rule: about 1% shrinkage for each 4% change in moisture content.
State and local inspectors check boards in stores. NIST worked with a lumber industry group and California to write step-by-step test procedures, using calipers, steel tapes and moisture meters, so every inspector measures the same way.
Source: National Institute of Standards and Technology, Making Sure that Lumber Measures Up (news, March 2017) (nist.gov)