use vertical, adjacent and supplementary angles to write and solve multi-step equations for unknown angles in a frame.
Phase 4: Build
Do Now. Workers on building sites lean ladders against walls every day. Before you read, make a prediction about the safety rule.
A worker leans a ladder with a working length of 16 feet against a wall. About how far from the wall should the foot of the ladder be?
The reading opens over the lesson; close it to come back to exactly where you were.
Ladders make angles. Where a ladder meets level ground, it makes two adjacent angles on a straight line: one on the wall side and one on the outside. They are supplementary. Following OSHA’s one-quarter rule puts the ladder at about 75° from the ground on the wall side, so the outside angle is about 180 − 75 = 105°. Builders often call it the 4-to-1 rule: one foot out for every four feet of ladder.
Vertical angles. When two straight lines cross, they make two pairs of opposite angles called vertical angles. Vertical angles are always equal. Any two angles next to each other at the crossing are adjacent and supplementary.
Worked example 1: Destiny’s X-brace. A shed wall has two boards that cross in an X. One angle measures (4x − 10)°, and the angle opposite it measures 110°. Vertical angles are equal, so 4x − 10 = 110. Add 10: 4x = 120. Divide by 4: x = 30. Each angle next to the 110° angle is 180 − 110 = 70°. Check: 4(30) − 10 = 110.
Worked example 2: Ravi’s ladder. Ravi’s ladder makes a 75° angle with the ground on the wall side. The outside angle is labeled 3(x + 5)°. The two angles are supplementary, so the outside angle is 105° and 3(x + 5) = 105. Divide both sides by 3: x + 5 = 35. Subtract 5: x = 30. Check: 3(30 + 5) = 3(35) = 105, and 105 + 75 = 180.
The fraction rule as an equation. If the foot of a ladder is 4.5 feet from the wall, what working length matches? (1/4)L = 4.5, so L = 4.5 × 4 = 18 feet. Fractions, decimals and whole numbers can all appear in the same problem.
Multi-step habit. Find the angle fact first (equal, 90 or 180), write the equation, solve it, then answer the question that was asked. Sometimes x is not the angle; you must substitute to find the angle.
Mark the equal angles and the supplementary pairs on each sketch before you write an equation.
Add an X-brace and a ladder sketch to your Cut and Angle notes.
Vertical angles at an X-brace measure (6x − 12)° and 102°. Solve for x and find all four angles at the crossing.
The foot of a ladder is 3.25 feet from the wall. Write and solve an equation with the one-quarter rule to find the working length. Is that a reasonable ladder length for a garden shed? Explain.
Equal across, 180 beside. That is the whole story of crossing lines.
Exit ticket: Kai solved 2(x + 10) = 140 by subtracting 10 first and wrote x = 65. Show his error and find the correct value of x.
Pacing: warm-up and reading 8 minutes, mini lecture 9, guided practice 13, independent 7, closure 3.
Likely misconceptions: thinking vertical means up and down (it means sharing a vertex); setting vertical angles to add to 180; undoing the steps of 2(x + 10) = 140 in the wrong order. Subtracting 10 first gives 2x = 130 and x = 65 (Kai’s error), but the 10 is inside the parentheses, so divide by 2 first: x + 10 = 70.
Supports: two pencils crossed on the desk to show vertical angles; highlighters for equal pairs. Note: the 75° figure comes from the one-quarter rule and is the common builders’ rounding; students do not compute it (that needs trigonometry). Stretch: if the ladder’s wall-side angle grows, what happens to the outside angle?
Answer guide: 48; x = 12; false; 30; 5 feet; x = 25. X-brace with 64°: 64 (vertical), 116 and 116 (supplementary). Independent: 6x − 12 = 102, 6x = 114, x = 19; angles 102, 78, 102, 78. (1/4)L = 3.25, L = 13 feet; reasonable for reaching a shed roof. Exit ticket: Kai treated 2(x + 10) as 2x + 10. Divide first: x + 10 = 70, so x = 60. Check: 2(60 + 10) = 140, while 2(65 + 10) = 150.
Occupational Safety and Health Administration, 29 CFR 1926.1053, Ladders · U.S. government work, public domain
The Occupational Safety and Health Administration, or OSHA, is the U.S. agency that writes safety rules for workplaces. Section 1926.1053 of its construction rules covers ladders.
One rule is about the angle of a ladder that leans against something. OSHA calls this a non-self-supporting ladder, because it cannot stand up on its own. It must be set so that the horizontal distance from the top support to the foot of the ladder is about one-quarter of the ladder’s working length. The working length is the length along the ladder from its foot to the top support. So a ladder with a 16-foot working length should have its foot about 4 feet out.
Other rules use numbers, too. When a ladder is used to reach an upper landing, its side rails must extend at least 3 feet above the landing. Rungs must be spaced at least 10 inches and at most 14 inches apart, measured center to center. Most portable ladders must hold at least four times the heaviest load they are meant to carry.
A rule written as a fraction is really a rule about an angle. Change the distance at the foot, and the angle between the ladder and the ground changes.
Source: Occupational Safety and Health Administration, 29 CFR 1926.1053, Ladders (osha.gov)