
write, solve and graph absolute value equations and inequalities that model tolerance and alarm situations, and interpret the solutions in context.
Instruction
The absolute value of a number is its distance from zero on the number line: |5| = 5 and |−5| = 5. More usefully, |x − a| is the distance between x and a. That single idea turns absolute value into a modeling tool.
Tolerance. A Central Coast grower packs strawberry flats labeled 12 pounds. The packing standard (illustrative) allows each flat to be off by at most 0.25 pound. If w is a flat’s weight, the requirement is “the distance between w and 12 is at most 0.25″:
|w − 12| ≤ 0.25
A distance of at most 0.25 from 12 means w is between 12 − 0.25 and 12 + 0.25, so 11.75 ≤ w ≤ 12.25. On the number line this is a closed interval, with filled circles because the endpoints are allowed:
Alarms. A school greenhouse is kept at 68°F, and an alarm sounds if the temperature t is more than 4°F away from that setting: |t − 68| > 4. Distance greater than 4 from 68 means t is below 64 or above 72. The solution is t < 64 or t > 72, two separate rays with open circles, because exactly 64 or 72 does not trigger the alarm:
The pattern: “less than” absolute value inequalities describe values close to the center and give one interval (an and statement). “Greater than” ones describe values far from the center and give two rays (an or statement).
Solving equations. Solve |2x − 5| = 9. The quantity inside is 9 units from zero, so it equals 9 or −9. Case 1: 2x − 5 = 9, so 2x = 14 and x = 7. Case 2: 2x − 5 = −9, so 2x = −4 and x = −2. Check both: |14 − 5| = 9 and |−4 − 5| = 9. An equation such as |x + 1| = −3 has no solution, because a distance cannot be negative.
Solving inequalities with a coefficient. Solve |2x − 5| ≤ 9. Write it as a compound inequality: −9 ≤ 2x − 5 ≤ 9. Add 5 to all three parts: −4 ≤ 2x ≤ 14. Divide by 2: −2 ≤ x ≤ 7. The endpoints are exactly the solutions of the equation you just solved.
Going backward. A delivery window runs from 60 to 70 minutes after an order. The center is 65 and the “radius” is 5, so the window is |m − 65| ≤ 5. To write any interval p ≤ x ≤ q as an absolute value inequality, use the midpoint (p + q)/2 and half the length (q − p)/2.
Workshop. Build three models from the situation cards (a pharmacy’s medicine dose tolerance, a speed-sensor alert, a thermostat, or a situation you choose). For each: write the absolute value statement, solve it, graph it and write one sentence interpreting the solution. State the precision of each measurement and why the tolerance makes sense for it.
📖 Read for this lesson
The reading opens over the lesson; close it to come back to exactly where you were. The checks below draw on it.
Formative check
Work through these before moving on. They are not graded — they tell you whether the standard below has landed yet.
Solve |x − 3| = 8.
A bolt must be 25 mm long with a tolerance of 0.2 mm. Which statement describes acceptable lengths L?
The solution of |2x − 5| ≤ 9 runs from x = negative up to x = , endpoints included.
The inequality |t − 68| > 4 has a solution set made of one interval between 64 and 72.
How confident are you that you can model a tolerance or alarm with absolute value, solve it and graph the solution?
Practice
Work these on paper or in your notebook, then open Check your answer. Aim for all of Fluency and Application; try at least one Challenge.
Printable version: this unit’s practice workbook (PDF)
Fluency
Build speed and accuracy with the core skill.
- Solve: |x − 4| = 7
Check your answer
Answer: x = −3 or x = 11x − 4 = 7 or x − 4 = −7. - Solve: |x + 2| = −2
Check your answer
Answer: No solutionAn absolute value is never negative. - Solve: |x − 1| = 4
Check your answer
Answer: x = −3 or x = 5x − 1 = 4 or x − 1 = −4. - Solve: |x − 5| = 4
Check your answer
Answer: x = 1 or x = 9x − 5 = 4 or x − 5 = −4. - Solve and graph: |x + 1| ≥ 9
Check your answer
Answer: x ≤ −10 or x ≥ 8Distance from −1 is at least 9: x + 1 ≤ −9 or x + 1 ≥ 9. - Solve and graph: |x + 5| < 8
Check your answer
Answer: −13 < x < 3Distance from −5 is less than 8: −8 < x + 5 < 8. - Solve and graph: |x + 1| ≥ 8
Check your answer
Answer: x ≤ −9 or x ≥ 7Distance from −1 is at least 8: x + 1 ≤ −8 or x + 1 ≥ 8. - Solve and graph: |x| < 8
Check your answer
Answer: −8 < x < 8Distance from 0 is less than 8: −8 < x < 8.
Application
Use the skill in context. Show your reasoning.
- Missouri pecan bags are labeled 16 oz with a tolerance of 0.3 oz. Write and solve an absolute value inequality for acceptable weights w.
Check your answer
Answer: |w − 16| ≤ 0.3, so 15.7 ≤ w ≤ 16.3Distance from 16 is at most 0.3. - An aquarium alarm sounds when the water is more than 3°F from 76°F. Write and solve the alarm condition.
Check your answer
Answer: |t − 76| > 3, so t < 73 or t > 79More than 3 away means two rays. - Solve |3x + 6| = 15.
Check your answer
Answer: x = 3 or x = −73x + 6 = 15 or 3x + 6 = −15. - A delivery arrives between 45 and 75 minutes after ordering. Write this as an absolute value inequality.
Check your answer
Answer: |m − 60| ≤ 15Midpoint (45 + 75)/2 = 60; half-width 15.
Challenge
Stretch problems. Expect to think before you write.
- Solve |2x − 7| ≤ x + 1.
Check your answer
Answer: 2 ≤ x ≤ 8Write −(x + 1) ≤ 2x − 7 ≤ x + 1. The left part gives x ≥ 2 and the right part x ≤ 8. Check x = 5: |3| = 3 ≤ 6.
Review
Keep earlier skills sharp.
- For the data 3, 3, 6, 19, 20, 26, 35, 35, 35: find the mean, median, range and interquartile range. (Find the quartiles as the medians of the lower and upper halves, leaving out the overall median when the count is odd.)
Check your answer
Answer: mean = 20.22; median = 20.0; range = 32; IQR = 30.5 (Q1 = 4.5, Q3 = 35.0) - The data 4, 6, 7, 9, 14 have mean 8. Find the standard deviation (divide by n) to two decimals.
Check your answer
Answer: 3.41Squared deviations sum to 58.
Real Tolerances: What the Law Allows a Pump, a Package and a Scale to Be Off By
NIST Handbook 44, Section 3.30, Liquid-Measuring Devices (retail motor fuel dispenser tolerances, as summarized by the NIST Office of Weights and Measures) and NIST Handbook 133 (2026), Appendix A, Table 2-5, Maximum Allowable Variations for Packages Labeled by Weight; retrieved September 23, 2026 · Public domain (works of the United States government); worked models SLS original
Why this reading. The workshop asks for three tolerance or alarm models built from “situation cards.” These are the cards, and they are not invented: every tolerance below is published by the National Institute of Standards and Technology and enforced by county weights-and-measures inspectors, including Missouri’s. A tolerance is exactly what |x − a| ≤ t was built to say, and these are the numbers real inspectors use.
1. The gasoline pump
NIST states: “A typical gasoline dispenser, in use, is given a maintenance tolerance of 1 cubic inch plus 1 cubic inch per indicated gallon. These devices are typically tested with a 5-gallon prover, so the tolerance per the 5-gallon test is ±6 cubic inches or ±98.32 milliliters. For newly installed devices, the acceptance tolerance is half the maintenance tolerance; for a 5-gallon test, it is ±3 cubic inches.”
Let V be the volume, in cubic inches, actually delivered when the pump says five gallons. One gallon is 231 cubic inches exactly, so five gallons is 1155 cubic inches. The maintenance requirement is
|V − 1155| ≤ 6, so 1149 ≤ V ≤ 1161,
and the acceptance requirement for a new pump is |V − 1155| ≤ 3, or 1152 ≤ V ≤ 1158. Both are closed intervals: a pump exactly 6 cubic inches short still passes. Six cubic inches out of 1155 is about 0.52%, or roughly two tablespoons in five gallons.
Notice the structure of the underlying rule. The tolerance is 1 + 1×(gallons) cubic inches, which is a linear expression with a constant term: a two-gallon test gets 3 cubic inches, a ten-gallon test 11. The constant 1 exists because even a perfect meter has to start and stop.
2. The package on a shelf
NIST Handbook 133 gives a maximum allowable variation, or MAV, for individual packages labeled by weight. It is a step table, not a percentage. Some of its rows:
| Labeled quantity | MAV |
|---|---|
| Less than 36 g, 0.08 lb, or 1.28 oz | 10% of labeled quantity |
| More than 2.88 oz to 4.16 oz | 7.2 g / 0.016 lb / ¼ oz |
| More than 9.28 oz to 11.20 oz | 14.5 g / 0.032 lb / ½ oz |
| More than 15.04 oz to 17.28 oz | 19.9 g / 0.044 lb / 11/16 oz |
| More than 2.14 lb to 2.48 lb | 35.3 g / 0.078 lb |
| More than 4.70 lb to 5.80 lb | 63 g / 0.14 lb |
| More than 11.70 lb to 14.30 lb | 113 g / 0.25 lb |
| More than 54.40 lb | 2% of labeled quantity |
A one-pound bag of rice is labeled 16 oz, which falls in the row “more than 15.04 oz to 17.28 oz,” so its MAV is 11/16 oz = 0.6875 oz. The model is
|w − 16| ≤ 0.6875, so 15.3125 ≤ w ≤ 16.6875 ounces.
Now look up the 12-pound flat of strawberries from the mini-lecture. Twelve pounds lies in the row “more than 11.70 lb to 14.30 lb,” whose MAV is 0.25 lb — exactly the tolerance the lesson used as an illustration. |w − 12| ≤ 0.25 gives 11.75 ≤ w ≤ 12.25 lb, and that is the real rule, not a teaching invention.
Two things worth arguing about. The MAV is not a fixed percentage: 0.6875 oz on a 16-oz package is 4.3%, while 0.25 lb on a 12-lb flat is 2.1%, and above 54.4 lb the table switches to a flat 2%. And the MAV applies to a single package; a separate rule requires the average of a lot to be at least the labeled quantity, so a packer may not simply aim low and stay inside the MAV every time.
3. Building the alarm form
A tolerance gives an “at most” statement and one interval. An alarm gives the opposite. Suppose an inspector’s handheld flags any five-gallon test that fails the maintenance tolerance: it sounds when |V − 1155| > 6, that is, when V < 1149 or V > 1161 — two rays, open circles, because a dispenser exactly 6 cubic inches off still passes. The same pair of statements, one “close to” and one “far from,” describes every tolerance in this reading.
Going backward. A county inspector says a scale passes if it reads between 49.98 and 50.02 pounds on a 50-pound test weight. Midpoint (49.98 + 50.02)/2 = 50, half-length (50.02 − 49.98)/2 = 0.02, so the rule is |x − 50| ≤ 0.02. Any interval converts this way, and converting it is how you check that a written rule and a written interval say the same thing.
Precision matters here. These tolerances are stated to two or three figures because the test equipment is that good. Writing a tolerance more precisely than the instrument can measure makes an unenforceable rule; writing it less precisely gives away product.