find the area of trapezoids and rhombuses by making parallelograms, rectangles and triangles out of them.
Phase 2: Investigate
Do Now. A garden bed along a sidewalk is a trapezoid: its top edge is 4 ft, its bottom edge is 10 ft, and it is 5 ft from top to bottom. Sketch it.
What happens if you put two copies of this trapezoid together, one turned upside down?
The reading opens over the lesson; close it to come back to exactly where you were.
Trapezoids. A trapezoid is a four-sided shape with at least one pair of parallel sides, called the bases. The height is the distance between the bases, at a right angle to them.
Worked example 1: two ways for one bed. Sofia’s bed has bases 4 ft and 10 ft and height 5 ft, with equal slanted sides. Way A, double it: two copies make a parallelogram with base 4 + 10 = 14 ft and height 5 ft. Its area is 14 × 5 = 70 ft², so one trapezoid is 70 ÷ 2 = 35 ft². Way B, cut it: the bed is a rectangle 4 ft by 5 ft (20 ft²) with a triangle on each side. The 10 ft base minus the 4 ft middle leaves 6 ft, or 3 ft for each triangle. Each triangle is 1/2 × 3 × 5 = 7.5 ft². Total: 20 + 7.5 + 7.5 = 35 ft². Both ways give 35.
The formula. Way A gives A = (b1 + b2) × h ÷ 2, which is NASA’s formula. Add the bases, multiply by the height, then halve.
Rhombuses. A rhombus has four equal sides. Its two diagonals (lines from corner to opposite corner) cross at a right angle and cut each other in half.
Worked example 2: a diamond bed. Marcus plans a rhombus bed with diagonals 6 ft and 8 ft. Way A: the diagonals cut it into 4 right triangles, each with legs 3 ft and 4 ft, so each is 1/2 × 3 × 4 = 6 ft² and all four are 24 ft². Way B: a rectangle 6 ft by 8 ft around the rhombus is 48 ft², and the rhombus fills exactly half of it: 24 ft².
Two rhombus tools. If you know a side and the height, use b × h, because a rhombus is a parallelogram. If you know the diagonals, multiply them and halve. Marcus’s rhombus has sides 5 ft, so its height is 24 ÷ 5 = 4.8 ft.
Use paper copies or grid paper. Try one problem both ways and compare.
Sketch each shape and label every number you use.
A trapezoid bed has bases 3 1/2 ft and 6 1/2 ft and height 3 ft. Its area is square feet. (Write a whole number.)
A rhombus has diagonals 6 ft and 8 ft and sides 5 ft. What is its height?
Design a trapezoid garden bed with an area of exactly 30 square feet. Give its two bases and its height, and show the check.
Every shape so far came from a rectangle. Next we break whole play areas into pieces we know.
Exit ticket: a trapezoid has bases 4 ft and 12 ft and height 3 ft. Find its area two ways.
Pacing: Do Now 4 min, reading 6, mini lesson 12, paper investigation 13, exit ticket 5.
Accuracy: the NASA formula is A = h * [t + b] / 2. PA eligible content M06.C-G.1.1.1 lists squares, rectangles, parallelograms, rhombuses and trapezoids; formulas are provided on the PSSA, so the goal is understanding why they work. Some books define a trapezoid with exactly one pair of parallel sides; the formula works either way. Way B in Example 1 splits the extra 6 ft evenly because the slanted sides are equal; for an uneven trapezoid the two triangles differ but still add to the same area.
Likely misconceptions: multiplying the sum of the bases by the height and forgetting to halve (gets 70 for Sofia’s bed); multiplying the diagonals of a rhombus without halving; using a slanted side as the trapezoid height.
Supports: paper trapezoids in pairs so students can build the parallelogram. Stretch: a trapezoid has area 36 ft² and height 4 ft; what can the bases be? (Any two that add to 18.)
Answer guide: a 30 ft² design: for example bases 4 and 8 with height 5 ((4 + 8) × 5 ÷ 2 = 30). Exit ticket: (4 + 12) × 3 ÷ 2 = 24 ft²; or rectangle 4 × 3 = 12 plus two triangles 1/2 × 4 × 3 = 6 each, so 12 + 6 + 6 = 24.
NASA Glenn Research Center, Beginner's Guide to Aeronautics: Area · U.S. government work, public domain
NASA’s Beginner’s Guide to Aeronautics shows wings and rocket fins as flat outlines called planforms. Besides rectangles and triangles, one planform on its list is the trapezoid.
A trapezoid has a top edge and a bottom edge that run side by side. NASA labels the top t, the bottom b and the distance between them, the height, h. The page gives the area as one half of the sum of the top and bottom, times the height. It writes the formula as A = h × (t + b) / 2.
Read that formula slowly. First add the top and bottom. Then multiply by the height. Then divide by 2. Engineers need the area to work out the lift and drag of a wing, which is why NASA says design engineers use this skill every day.
The page puts the trapezoid formula beside the rectangle and triangle formulas. That is a clue for us. A trapezoid can be cut into a rectangle and triangles, or doubled into a parallelogram. Today we try both ways and check that they agree with NASA’s formula.
Source: NASA Glenn Research Center, Beginner's Guide to Aeronautics: Area (grc.nasa.gov)